✅ Updated Nov 2026
Affiliate Disclosure: As an Amazon Associate, we earn from qualifying purchases. Links marked "Check on Amazon" are affiliate links — learn more.

To install RAM in a gaming PC, power it off and unplug it, open the slot clips, line the notch on the module up with the key in the slot, press down firmly on both ends until the clips snap shut, and then enable the XMP or EXPO profile in the BIOS so the kit runs at its rated speed. For two modules, use the slots your motherboard manual marks for dual-channel operation, which is commonly the second and fourth slots counted from the processor.

Before you start: confirm what fits

Memory type must match the board. Current platforms such as AMD Ryzen 9000 on AM5 and Intel Core Ultra 200S use DDR5 only, and DDR4 and DDR5 modules are keyed differently so they cannot be exchanged. Intel’s specification page for the Core Ultra 9 285K, for example, lists DDR5 up to 6400 MT/s with two memory channels. Older LGA 1700 boards could be DDR4 or DDR5 depending on the board, so read the model number printed on the motherboard.

CheckWhere to find it
Memory type (DDR4 or DDR5)Motherboard specifications page or the board’s slot labels
Maximum capacity and slot countMotherboard manual, memory section
Qualified kit listSupport page for the exact board model
Cooler clearanceCooler maker’s specification for memory height
BIOS version for new CPUsSupport page; some boards need an update for newer processors

What you need

  • Your memory kit, kept in its packaging until the moment of installation.
  • A clear surface and good light.
  • The motherboard manual, for the slot diagram.
  • Optional: an anti-static wrist strap. Touching bare, unpainted case metal before handling parts is the usual alternative.

No screwdriver is needed for the memory itself, though you may need one to remove a side panel.

Step-by-step installation

  1. Shut down and unplug. Turn the PC off, switch the power supply off at its rocker switch and pull the power cable. Press the case power button once to drain residual charge.
  2. Open the case. Remove the side panel and lay the case flat if you are more comfortable that way. Locate the memory slots, the long narrow connectors next to the processor socket.
  3. Clear the way. If a large air cooler or cable blocks access, move cables aside. Some builders find it easier to install memory before the cooler goes on.
  4. Find the correct slots. For two modules, check the manual diagram. Many boards use the second and fourth slots from the processor for a pair, but not all do. If you install only one module, the manual will say which slot to use.
  5. Open the clips. Push the retention clip at the end of each slot outward. Some boards have a clip on only one end.
  6. Align the notch. Hold the module by its edges. Match the notch in the gold strip with the key in the slot. The notch is offset, so it only fits one way around.
  7. Press down. Apply even, firm pressure on both ends of the module, or alternate between them, until it drops into the slot and the clips snap upright on their own. A click and a flush fit show that it is seated.
  8. Check the seating. Look along the slot. The module should sit level with no visible gold showing beyond the slot edge, and both clips should be closed.
  9. Close up and power on. Reconnect power, switch the power supply back on and start the PC. The first boot can take longer than usual on DDR5 platforms, because the board trains the memory when it first sees new modules. Stay patient for a few minutes before assuming something is wrong.

Enable the speed profile in the BIOS

After you install a fast kit, it often starts at a basic default speed instead of the speed on the label. To get the rated performance, enter the BIOS during startup, find the memory or overclocking page, and enable the profile stored on the kit. Menu names vary by motherboard maker, so check the manual for the exact path. AMD-oriented kits use EXPO profiles, and Intel-oriented kits use XMP profiles, although many boards read either.

Keep in mind that a profile above the processor’s official memory speed counts as overclocking by processor makers. It can affect warranty terms and, rarely, stability. If the system fails to boot or crashes after enabling it, reset BIOS defaults using the clear-CMOS option described in your manual and update the BIOS.

Confirm the installation worked

WhereWhat to look for
BIOS memory pageTotal capacity matches what you installed
Operating system system informationInstalled memory amount, and speed if shown
Task Manager memory tab (Windows)Speed, slots used and form factor
Memory diagnostic toolNo errors after an extended run

Slot layout guide

ModulesCommon practiceWhy
1Use the slot named in the manualEnsures the board boots reliably
2Slots two and four counted from the CPU, unless the manual says otherwiseGives dual-channel operation
4Fill all slots with a matching kitRaises capacity, but board makers commonly note a lower supported speed

Common mistakes

  • Not pressing hard enough. Memory needs firm pressure, and a half-seated module is a frequent cause of no-display boots.
  • Using the wrong slots. Two modules in adjacent slots may run in single-channel mode and give lower bandwidth.
  • Forcing a module in the wrong direction. If it will not seat, remove it and check the notch.
  • Skipping the profile. The kit runs slowly until you enable it.
  • Mixing kits. Modules from different kits run at the weakest shared setting and can fail to boot.
  • Touching the gold contacts. Skin oils can disturb the connection.

Troubleshooting after installation

SymptomLikely causeFix
No display, fans spinMemory training in progress, or module unseatedWait several minutes, then power down and reseat.
Memory error light on boardModule not detectedReseat and try the manual’s recommended slot.
Only half the capacity showsOne module not seatedPower down and press both modules in firmly.
Runs slower than the labelProfile not enabledEnable XMP or EXPO in the BIOS.
Crashes after enabling profileSetting too demandingReset defaults, update BIOS, try a lower speed.

If problems persist, contact the motherboard or memory maker, or take the PC to a technician.

Pick-by-situation table

SituationBest approach
New build, two modulesInstall in the manual’s dual-channel slots and enable the profile.
Upgrading from 16 GB to 32 GBReplace the old kit with a new matched pair if the slots allow.
Adding modules to an old kitMatch speed and capacity as closely as possible, expecting a lower common speed.
Boot problems after installReseat, test one module at a time, update BIOS.

Frequently Asked Questions

Which RAM slots should I use for two sticks?

Many boards expect the second and fourth slots counted from the processor, but the layout differs between models. Check the motherboard manual’s memory diagram, since the wrong slots may cause single-channel operation or a failure to boot.

Do I need to turn off the PC to install RAM?

Yes. Shut it down, switch off the power supply and unplug the cable before touching memory. Hot-swapping desktop memory risks damage to the module and the board.

Why does my new PC take a long time to boot after installing RAM?

DDR5 boards often run memory training on first boot or after hardware changes, which can take a few minutes. If the screen stays blank for a long period, power off, reseat the modules and consult the manual.

Do I have to enable XMP or EXPO?

You do not have to, but without it the kit usually runs at a basic default speed rather than the speed on the label. Enabling the profile is a setting beyond the processor’s official rating, so keep it conservative if you see instability.

Can I install one RAM stick now and add another later?

You can, and the system will work in single-channel mode until you add the second. Buying a matched two-module kit from the start gives better and more predictable results.

Explore Our Guides & Free Tools