✅ Updated Nov 2026
Affiliate Disclosure: As an Amazon Associate, we earn from qualifying purchases. Links marked "Check on Amazon" are affiliate links — learn more.
⭐ Key Takeaways
Quick answer: Our top pick is Samsung 990 PRO 2TB, with WD Black SN850X 2TB as a strong alternative.

Upgrading your boot drive used to mean a full Windows reinstall, a day of drivers, and a week of rediscovering settings. Cloning skips all of that. A proper clone copies your existing drive bit by bit, including the hidden partitions Windows needs to start, so the new SSD boots into the exact system you left: same desktop, same game installs, same saves. The process is safe when done in the right order, and risky only when steps get skipped. This guide walks through the whole job, from the checks you run before touching a cable to the first boot and the partition fix most people forget.

As an Amazon Associate, we earn from qualifying purchases.

Quick Answer

Clone the whole disk, not just the main partition, using the drive maker’s free cloning tool or a reputable disk utility. Connect the new SSD, run the clone without interrupting it, then boot from the new drive with the old one disconnected. Finally, extend the Windows partition to fill the larger drive and keep the old SSD untouched for a week as your fallback.

What a Clone Copies That a File Copy Misses

A modern Windows drive is not one partition. Alongside the main volume sit a small EFI system partition that tells the motherboard how to start Windows, a recovery partition, and sometimes a reserved partition the installer created. Dragging your folders to a new SSD copies none of that structure, which is why a file copy produces a drive full of your data that the PC refuses to boot from.
Cloning software copies every partition in order, with the boot configuration intact, and adjusts the layout when the target is a different size. That completeness is the entire point. It is also why the golden rule is to clone the disk as a whole and let the software handle partitions, rather than picking volumes one at a time and hoping the boot pieces come along.

Before You Start: Four Checks That Prevent Failures

Most failed clones fail for reasons a few minutes of checking would have caught.

First, compare sizes honestly. The target needs enough room for the data actually stored on the source, not the source drive’s full capacity. Cloning a 1TB drive holding 300GB of data onto a 500GB SSD works fine with most tools, which shrink the main partition to fit. Cloning onto a target smaller than the used data does not work at all.

Second, check the source drive’s health. A clone copies errors as faithfully as files, and a dying source can stall halfway. If your drive already throws read errors or disappears from BIOS, back up your irreplaceable files first and treat the clone as a bonus, not a plan.

Third, deal with encryption. If BitLocker protects your Windows volume, suspend it before cloning and resume it after the first successful boot. Cloning an actively encrypted volume unprepared is the most common cause of a new drive that boots to a recovery screen.

Fourth, protect the session. Plug laptops into the charger, and do not start a long clone during a storm or on a tripping circuit. A clone that loses power midway leaves the target half-written, and you simply start it over.

Step 1: Connect the New Drive

The cleanest setup is a free slot. If your motherboard has a second M.2 slot, install the new SSD there, and both drives stay internal for the whole job. Initialize the new drive in Disk Management only if the cloning tool asks; most tools detect a blank drive on their own. If asked for a partition style, choose GPT, which matches every modern Windows installation.

If your board has a single M.2 slot, or you are upgrading a laptop, an external NVMe enclosure is the bridge. The new SSD goes in the enclosure, connects over USB, and receives the clone exactly as if it were internal. Afterward you swap the drives physically, and the enclosure becomes the old SSD’s new home.

Step 2: Run the Clone and Let It Finish

Drive makers bundle capable cloning tools with their SSDs. Samsung’s Data Migration handles Samsung targets, WD and SanDisk drives include an Acronis True Image license, and general utilities such as Macrium Reflect cover everything else. Whichever you use, the workflow is the same: select the entire source disk, select the target, confirm the proposed partition layout, and start.

Two decisions matter here. Choose the whole-disk option rather than partition-by-partition copying, for the boot reasons above. And if the tool offers to adjust partitions for a larger target, accept it, but do not panic if the Windows volume still arrives at its old size; extending it later takes a minute.
Then leave the machine alone. A clone of a few hundred gigabytes internally typically finishes in well under an hour; over USB it takes longer. Do not sleep the PC, close the lid, or cancel because the progress bar pauses. Partition copies move at uneven speeds, and a quiet bar is normal.

Step 3: The First Boot and the Forgotten Partition Fix

Shut the PC down. Before powering it back on, disconnect or remove the old drive, or enter BIOS and set the new SSD first in the boot order. This step is not superstition: with two drives carrying identical boot signatures attached, some boards start from the old drive and you end up testing nothing. Booting once with only the new drive present proves the clone worked.

Windows should load exactly as before. Run three quick confirmations. Check that your files and games are present. Open Disk Management and look at the layout. Then check the size of the Windows volume, because the classic cloning leftover is unallocated space behind it when the target is larger than the source. Right-click the Windows partition, choose Extend Volume, and claim the free space. Finally, confirm Windows recognizes the drive as an SSD in the Optimize Drives panel, which keeps TRIM active.

Step 4: Keep the Old Drive as a Fallback, Then Reuse It

Do not wipe the old drive the same day. Use the system normally for about a week. If anything odd surfaces, your complete previous system is one drive swap away. Once the new drive has earned trust, format the old one and reuse it as a game library drive or as backup storage in that USB enclosure. And remember a clone is not a backup by itself: the T7 Shield below holds a separate copy of files you cannot replace, stored outside the PC.

The Hardware That Makes Cloning Painless

The target drive is the decision that outlives the afternoon you spend cloning. These five products cover the roles the process needs: three internal targets at three tiers, the enclosure for single-slot upgrades, and a rugged portable drive for the safety copy.

Samsung 990 PRO 2TB

Samsung 990 PRO 2TB NVMe SSD

Samsung 990 PRO 2TB NVMe SSD

Check price on Amazon

The premium target. Its sequential speeds top the PCIe Gen4 class, which shortens both the clone itself and every load afterward, and 2TB holds a full Windows install plus a large game library without rationing.

Specs:
– Capacity: 2TB
– Interface: PCIe Gen4 x4, NVMe, M.2 2280
– Sequential read: up to 7,450 MB/s
– Sequential write: up to 6,900 MB/s

WD Black SN850X 2TB

WD Black SN850X 2TB NVMe SSD

WD Black SN850X 2TB NVMe SSD

Check price on Amazon

The gaming-tier target, with strong sustained writes that suit a clone writing hundreds of gigabytes in one session as well as the installs that follow it.

Specs:
– Capacity: 2TB
– Interface: PCIe Gen4 x4, NVMe, M.2 2280
– Sequential read: up to 7,300 MB/s
– Sequential write: up to 6,300 MB/s

Crucial P3 Plus 2TB

Crucial P3 Plus 2TB NVMe SSD

Crucial P3 Plus 2TB NVMe SSD

Check price on Amazon

The budget target. It gives you the full 2TB at Gen4 speeds that feel close to the premium drives in everyday loading, which is exactly the trade a boot-drive upgrade should make.

Specs:
– Capacity: 2TB
– Interface: PCIe Gen4 x4, NVMe, M.2 2280
– Sequential read: up to 5,000 MB/s
– Sequential write: up to 4,200 MB/s

UGREEN M.2 NVMe SSD Enclosure

UGREEN M.2 NVMe SSD Enclosure

UGREEN M.2 NVMe SSD Enclosure

Check price on Amazon

The connector for single-slot boards and most laptops. The new SSD clones over USB inside this aluminum enclosure, then the drives swap places and the old SSD moves in as fast external storage.
Specs:
– Interface: USB 3.2 Gen 2, up to 10Gbps, USB-C
– Compatibility: NVMe M-Key and B+M Key drives
– Supported sizes: 2230, 2242, 2260, 2280
– Features: UASP and TRIM support

Samsung T7 Shield 2TB

Samsung T7 Shield 2TB Portable SSD

Samsung T7 Shield 2TB Portable SSD

Check price on Amazon

The safety net. Before any clone, copy your irreplaceable files here. It is rated IP65 against water and dust and survives drops onto hard floors, so the backup can live in a drawer or a bag instead of inside the machine being upgraded.

Specs:
– Capacity: 2TB
– Interface: USB 3.2 Gen 2, USB-C
– Sequential read: up to 1,050 MB/s
– Sequential write: up to 1,000 MB/s

How to Choose

Start with capacity, because cloning is usually an upgrade, not a lateral move. Match the target to at least the size of your current drive, and step up a tier if your library keeps outgrowing its home; cloning onto a larger drive costs one Extend Volume click, while cloning onto a full one buys you a repeat of this job next year. Next, match the drive to your slot: a Gen4 drive in a Gen3 slot still works, simply at Gen3 speeds, so a premium target is never wasted. Finally, decide your connection path before buying: a free M.2 slot needs no accessories, a single-slot board or laptop needs the enclosure, and every setup benefits from an external backup drive.

Who Should Skip

Skip cloning and do a fresh Windows install instead if your current system is infected, unstable, or carrying years of accumulated breakage, because a clone preserves all of that faithfully. Skip it if the source drive is physically failing and throwing read errors; rescue the files first and reinstall onto the new drive. Skip it if you are changing platforms at the same time, such as moving between very different motherboard generations, where a clean install avoids a layer of driver conflicts.

Frequently Asked Questions

Will cloning copy my Windows activation and game licenses?

Yes. Activation is tied to your motherboard and digital license, and the same installation on the same machine stays activated. Games, launchers, and settings carry over as part of the copied volume.

Can I clone to a smaller SSD than my current drive?

Yes, as long as the data stored on the source is smaller than the target’s capacity. Most cloning tools shrink the main partition automatically to fit. If the used data exceeds the target, delete or move files first.

Why does my new SSD show the old drive’s size in Windows?

The clone copied the old partition layout, leaving the extra space unallocated behind the Windows volume. Open Disk Management, right-click the Windows partition, and choose Extend Volume to absorb it.

What should I do if the PC will not boot from the cloned drive?

Reconnect the old drive and boot from it; your system is untouched. Then repeat the clone with the whole-disk option selected, make sure BitLocker was suspended, and on the next attempt set the new SSD first in the boot order with the old drive disconnected.

Final Verdict

Cloning is the upgrade that respects your time: an hour of methodical work for your existing Windows setup, untouched. Connect the target properly, clone the whole disk, prove the first boot with the old drive disconnected, and extend the partition to claim your new space. Pick a target with room to grow, add the UGREEN enclosure if your board has one slot, and keep a T7 Shield as the backup outside the PC. Do those things in that order, and the riskiest part of the job is deciding what to install with all the space you just gained.

Explore Our Guides & Free Tools